富里叶级数的收敛速度

对正弦和余弦富立叶级数,通过合并相邻同号项,使其重排成交错级数.讨论了重排形成的交错级数的敛散性.指出根据自变量x的不同取值,该交错级数可能是单调递减或周期递减的级数.按照莱布尼茨判定法提出了不同精度要求的级数项数的计算公式.选取一到三阶收敛的富立叶级数计算了不同比值精度及差值精度要求的级数项数.计算表明,在x的取值为2π的等分点时,富立叶级数的部分和随项数的增加单调地逼近其收敛值.在x的取值为其它点时,富立叶级数的部分和随项数的增加围绕收敛值上下变动,周期地逼近其收敛值.低收敛阶富立叶级数的收敛速度较慢.要达到0.01%的精度,一收敛阶富立叶级数需要数万项,二收敛阶富立叶级数也需要数百项.在不同计算点处,要达到相同的计算精度,需要的级数项数差别较大.     

The differentiation operator in the space of uniformly convergent Dirichlet series

Continuity, compactness, the spectrum and ergodic properties of the differentiation operator are investigated, when it acts in the Fréchet space of all Dirichlet series that are uniformly convergent in all half-planes for each . The properties of the formal inverse of the differentiation are also investigated.     

The Crank–Nicolson finite spectral element method and numerical simulations for 2D non-stationary Navier–Stokes equations

In this paper, we first build a semi-discretized Crank–Nicolson (CN) model about time for the two-dimensional (2D) non-stationary Navier–Stokes equations about vorticity–stream functions and discuss the existence, stability, and convergence of the time semi-discretized CN solutions. And then, we build a fully discretized finite spectral element CN (FSECN) model based on the bilinear trigonometric basic functions on quadrilateral elements for the 2D non-stationary Navier–Stokes equations about the vorticity–stream functions and discuss the existence, stability, and convergence of the FSECN solutions. Finally, we utilize two sets of numerical experiments to check out the correctness of theoretical consequences.     

Three-dimensional interfacial fracture analysis of a one-dimensional hexagonal quasicrystal coating

In this paper, the three-dimensional (3D) interfacial fracture is analyzed in a one-dimensional (1D) hexagonal quasicrystal (QC) coating structure under mechanical loading. A planar interface crack with arbitrary shape is studied by a displacement discontinuity method. Fundamental solutions of interfacial concentrated displacement discontinuities are obtained by the Hankel transform technique, and the corresponding boundary integral-differential equations are constructed with the superposition principle. Green’s functions of constant interfacial displacement discontinuities within a rectangular element are derived, and a boundary element method is proposed for numerical simulation. The singularity of stresses near the crack front is investigated, and the stress intensity factors (SIFs) as well as energy release rates (ERRs) are determined. Finally, relevant influencing factors on the fracture behavior are discussed.     

InSb芯片碎裂与迸溅金点的关系

批量生产中经常发生的锑化铟(InSb)芯片碎裂问题制约着InSb红外焦平面探测器(IRFPAs)成品率的提升.经分析认为:低周期液氮冲击下发生在器件边沿区域的InSb芯片破碎与该区域中迸溅金点的存在有关.为从理论上明晰迸溅金点对InSb芯片局部碎裂的影响,本文建立了包含迸溅金点的InSb IRFPAs结构模型,分析了迸溅金点的存在对应力分布的影响.在此基础上,在应力集中处预置不同长度的初始裂纹用以描述InSb晶片中的位错,以能量释放率为判据,探究InSb芯片碎裂与迸溅金点和位错线长短的关系.结论如下:1)迸溅金点的存在对InSb芯片碎裂的影响是局部的,在迸溅金点与InSb芯片接触区域的两侧会形成两个应力集中点; 2)环绕预置裂纹的能量释放率会随着预置裂纹长度的增加而加速增大,当预置裂纹长度接近InSb芯片上表面时,能量释放率近乎指数增加,并在预置裂纹贯穿InSb芯片时达到最大值; 3)迸溅金点引起的InSb芯片破碎属于Ⅰ型断裂失效模式,在多周期液氮冲击中,位错线在应力集中效应的驱使下逐步扩展,直至贯穿InSb芯片,最终形成宏观碎裂失效现象.     

UHMWPE纤维的超临界CO_2辅助渗透预处理研究

利用Minitab软件设计实验,以超高分子量聚乙烯纤维(UHMWPE)为原料,研究了在不同的超临界CO_2流体状态下,处理压力、温度和时间等因素对三羟甲基丙烷三甲基丙烯酸酯(TMPTMA)渗入率的影响,确定了最佳因素设置范围;通过单因子实验优化了超临界CO_2处理工艺,并对经过电子束辐照的UHMWPE纤维凝胶含量和蠕变率进行了测试。研究结果表明:处理温度对TMPTMA的渗入率影响最大,其次为压力,时间的影响最小,确定了最优工艺条件为处理压力25MPa,温度80℃,时间30min;TMPTMA渗入率越高,电子束辐照后UHMWPE纤维的增感辐照交联效应和抗蠕变效果越好。     

A filter method for nonlinear semidefinite programming with global convergence

In this study, a new filter algorithm is presented for solving the nonlinear semidefinite programming. This algorithm is inspired by the classical sequential quadratic programming method. Unlike the traditional filter methods, the sufficient descent is ensured by changing the step size instead of the trust region radius. Under some suitable conditions, the global convergence is obtained. In the end, some numerical experiments are given to show that the algorithm is effective.